pressure center

Affects of Rotor Magnetic Field Center Deflection and Rotor Pole Center Suspending Difference to the Pressure on Thrust Pad in Large Synchronous Machines

大型同步电动机转子磁场中心安装偏差及转子磁极中心挂装高程差对推力瓦受力的影响

Dissociation and ionization of air bring on lower drag coefficients of the orbiter than that obtained from perfect gas model, while the location of pressure center moves forward.

空气的离解和电离导致轨道器的阻力系数比完全气体计算值低，压心位置前移。

The form of the array is a uniform vertical pressure sensor array, in whose center there is one three-dimensional vector hydrophone. By this combination array, the three-dimensional parameters of the near-field sources including the azimuth angle, the elevation angle and the distance can be achieved.

该算法采用均匀垂直声压阵中心配置单只三维矢量水听器的基阵形式，即可完成对近场源方位角、俯仰角和距离的三维参数估计。

Design and Implementation of an Internet Based ECG and Blood Pressure Telemonitoring Center

基于Internet心电血压远程监护系统的中心站设计与实现

Study of Stamping Die Pressure Center Fast Confirm in SolidWorks

冲裁模压力中心在SolidWorks中的快速确定探讨

A new method to determine the pressure center of pressing die& computer drawing method

确定冲模压力中心的计算机作图法

Based on the analysis of a large numerical examples, pressure spike amplitude equation and hertz center pressure formula of heavy loaded point contact elastohydrodynamic lubrication are fitted out by the least squares data fitting method.

在分析大量数值算例的基础上，利用最小二乘法拟合出了重载点接触弹流的二次压力峰公式和赫兹中心压力公式。

High water temperature, high humidity, and a low pressure center, to name a few.

京晶：比如说，高水温、高湿和低气压中心。

The Calculation of the Temperature Equilibrium and the Shaft Center Trajectory for a Dynamically Loaded Journal Bearing(ⅱ)& Nonzero Inlet Pressure

动载轴承温度平衡和轴心轨迹计算（Ⅱ）&进油压力不为零的情况

Puts forward the solutions for the welding equipment, greatly reduces the adverse impact to welding sealing performance brought by the mechanical equipment defects by improving hydraulic pressure, adjusting the concentricity of welding jig, improving the structure of center diaphragm tensioning device and oil filled machine.

提出了焊接设备改良方案，通过提升液压站压力、调整焊接夹具同心度、改进中心膜片张紧设备和充油机结构，大大降低了机械设备缺陷对焊接密封性能造成的不利影响。

YAO MING, HOUSTON ROCKETS CENTER: Everything looks perfect on pictures, I mean those X-ray pictures, and today, I'm walking on it well, full pressure on my foot already.

前休斯敦火箭队中锋姚明：在照片上，我是说X光片，一切看起来都非常完美。一直到今天，我走起路来也都没有问题，已经把全身重量都压在脚上了。

The center of pressure is about 1-11 / 2 diameter in front of the center of gravity.

压力中心大约在重心之前 1-11/2 直径.

The center area of the hollow spindle head end presents obvious negative pressure, the negative pressure is helpful for fiber sucked smoothly into yarn end.

空心锭头端中心区域呈现明显的负压，这种负压随着喷嘴入口气压的增大而增大，负压有利于纤维顺利被吮吸进入纱体尾端。

The fluid flow in the fracture is assumed to be linear. The tangential flow rate is proportional to the pressure gradient in the fracture, and the normal flow rate is proportional to the pressure difference between the fracture center and the fracture top/ bottom surface.

流体在裂缝中的流动是线性的，切向流动的速率与缝内压力梯度成正比，法向流动的速率与裂缝中心和裂缝上下表面的压差成正比。